SLITTERS
CLICK TO HOME PAGE from Sheet Metal Slitters

Sheet Metal SLITTING MACHINES
Click to request a quote with literature or call 773-334-5000 to order a machine. M-F 8AM-5PM CST

GARY single cut Slitter
 Sturdy 24 inch throat slitter with quick adjusting back gauge and scale. Shown without optional stand. Made in USA.
Click to request a formal quote for this machine
• Die-set type gauge mounting that insures easy setting and consistent squareness.
• Gauge mounting rods are extended to provide convenient carrying handles.
• Gauge is easily removed for machine transport and re-installed with no resquaring.
• Slitter knives are proven GARY "quickset" design manufactured from tool steel.
• Knives are outboard mounted for easy access knives are reversible , intervals between sharpening is double that of a single edge knives.
• "Adiprene" stripper rings are non-marking and serve to hold the material flat reducing twist.
• Dual bearings mounted at knife end to minimize deflection and increase knife life.
• Heavy duty roller chain drive with by 1/3 HP gearmotor.
• Standard 110 volt with grounded plug. 6 amps.

GARY 3354 Rotary Slitter $2350.
Capacity: 16 Gauge (.06")
Throat: 24"
Motor: 1/3 HP, 110 volts
Minimum Slitting Width: 1"
Maximum Slitting Width: 24"
Shipping Weight: 450 lbs.

GARY medium duty sheet fed multiple cut Slitting machines

GARY 3351 Economy Slitter

Click to request a formal quote for this machine
• 3" diameter cold - roll turned, ground and polished shafts mounted in dual wall ball bearings lubricated for life.
• Gauge mounted on each side for left or right hand use.
• End frames are aluminum - magnesium alloy.
• Rugged lightweight GARY torsion tube assembly.
• Heavy gauge steel with "T" bar reinforcement.
• Slitter knives are proven GARY "quickset" design manufactured from tool steel.
• Knives are "reversible", intervals between sharpening is double that of a single edge knives.
• 2 sets of standard 3" X 5" X 3/4" wide high-carbon tooling is included.
• 40 FPM standard operating speed.
• Heavy duty roller chain drive powered by 1/3 HP gearmotor.
• Standard 110 volt with grounded plug.
• Maximum sheet width: 49"
• Cutting rate: 40 feet per minute
• Machine weight: 480 Lbs.
• Made in USA

 Maximum number of simultaneous cuts:
30 gauge (.015") metal: 6 cuts
28 gauge (.018") metal: 4 cuts
26 gauge (.021") metal: 3 cuts
24 gauge (.024") metal: 3 cuts
22 gauge (.031") metal: 3 cuts
20 gauge (.036") metal: 2 cuts
18 gauge (.048") metal: 1 cut
16 gauge (.060") metal: 1 cut

GARY 3350 Super Duty Slitter

Click to request a formal quote for this machine
• 3" diameter cold - roll turned, ground and polished shafts mounted in dual wall ball bearings lubricated for life.
• Gauges on both sides for left or right hand use.
• Rugged lightweight GARY Torsion Tube end frames are of aluminum-Magnesuim alloy.
• Heavy steel table with "T" bar reinforcement.
• 3/4 H.P. gearhead motor. Choose model 3350 with 110 volts or 220 volts, single phase or model 3353 with 220 volts or 440 volts, 3 phase.
• Motors provided with thermal overload protection by means of an electrical motor starter.
• Available in either 40, 60, 80, or 100 Feet Per Minute.
• Remote hand pendant for easy knife settings.
• Stripper fingers provide for a twist-free cut.
• Standard knives 3/4 " thick X 3 " I.D. X 5 " O.D. High - carbon or optional high - carbon high - chrome steel
• Maximum sheet width: 49"
• Machine weight: 600 Lbs.
• Made in USA

 Maximum number of simultaneous cuts:
30 gauge (.015") metal: 12 cuts
28 gauge (.018") metal: 8 cuts
26 gauge (.021") metal: 6 cuts
24 gauge (.024") metal: 4 cuts
22 gauge (.031") metal: 4 cuts
20 gauge (.036") metal: 3 cuts
18 gauge (.048") metal: 2 cuts
16 gauge (.060") metal: 1 cut

GARY heavy duty sheet fed multiple cut Slitter machines

These heavy duty slitters are made for high speed slitting of hand fed of sheets of metal.
Depending upon which of the 6 different models you select, up to 21 cuts can be made in one pass.
Also, metal up to 10 gauge (.135") thick can be used if the slitter model 648 or 660 is purchased.
• Adjustable squaring arm
• Adjustable top arbor penetration
• Precision dial indicator Read-out
• 3 sets of easy change out knives
• Quick set knife design
• T-handle allen wrench
• Both arbors driven thru gears
• Tapered main arbor bearings
• Rubber stripper rings prevent twisting, scratching, and sticking
• Made in USA
Options:
* Extra tooling
* Variable speed drive
* Centering type entry guides
* Passline rolls
* Overrunning clutch
* Air clutch/brake

Photo showing GARY Slitter features.

Click on the Model Number to request a formal quote that machine
Specifications
26 gauge (.021")
-
17 cuts
-
-
-
-
24 gauge (.025")
-
13 cuts
-
-
-
-
22 gauge (.031")
15 cuts
8 cuts
-
19 cuts
-
-
20 gauge (.037")
10 cuts
5 cuts
-
13 cuts
-
-
18 gauge (.049")
5 cuts
3 cuts
13 cuts
7 cuts
-
19 cuts
16 gauge (.061")
3 cuts
2 cuts
8 cuts
5 cuts
-
12 cuts
14 gauge (.076")
1 cut
-
3 cuts
2 cuts
14 cuts
8 cuts
12 gauge (.105")
-
-
1 cut
-
6 cuts
4 cuts
10 gauge (.135")
-
-
-
-
2 cuts
1 cut
Max Sheet Width
49.5"
61.5"
49.5"
61.5"
49.5"
61.5"
Pass Line Height
38"
38"
38"
38"
38"
38"
Knife Arbor diameter
4"
4"
5"
5"
6"
6"
Knife size
4" x 6" x 1"
4" x 6" x 1"
5" x 7" x 1.5"
5" x 7" x 1.5"
6" x 9" x 1.5"
6" x 9" x 1.5"
Motor size
1 HP
1 HP
3 HP
2 HP
7.5 HP
5 HP
Voltage
120 volts, 1 phase, 60 Hz
Choose 240 volts or 480 volts, 3 phase, 60 Hz
Speed
80 fpm
80 fpm
100 fpm
100 fpm
100 fpm
100 fpm
Machine Weight
1300 Lbs
1600 Lbs
2200 Lbs
2500 Lbs
3000 Lbs
3300 Lbs

Click for American Machine Tools Company Homepage

 

American Machine Tools Corp.
 5864 Northwest Hwy
Chicago IL 60631 USA
Phone: 773-334-5000
Fax: 773-442-0314
Click to email us

 Terms & Conditions

Frequently Asked Questions

 Privacy Clause
Information in this website is subject to change without notice.
Offers from American Machine Tools Corporation include include Terms and Conditions shown on our website.
Liability is strictly limited to those warranties of fitness for purpose and safety as provided by the manufacturer.
Products and Logos in this website are trademarks or registered trademarks of their respective companies or mark holders.